Essai de Régénération des Huiles Moteurs Usagées par Percolation à l’aide d’Argile Rouge activée
DOI :
https://doi.org/10.59228/rcst.026.v5.i2.280Mots-clés :
Huiles lubrifiantes usagées, pollution, régénération, disques filtrants en argile activée, paramètresRésumé
Les huiles lubrifiantes usagées, après leur vidange, sont souvent rejetées dans l’environnement. Elles ont un impact à la fois sur la santé humaine et sur l’environnement lorsqu’elles ne sont pas correctement éliminées et gérées. En effet, la pollution environnementale constitue aujourd’hui l’un des problèmes majeurs auxquels l’humanité est confrontée. Plusieurs facteurs aggravent cette pollution, notamment le rejet incontrôlé des huiles moteurs usagées.
Le besoin d’un environnement exempt de toute menace toxique ne cesse de croître au sein de la société. Le présent travail vise à régénérer les huiles lubrifiantes usagées à l’aide de disques filtrants en argile activée. Les résultats montrent que certains paramètres, tels que la densité, la viscosité cinématique, l’indice de viscosité, le point d’éclair et le point d’écoulement, ont subi des modifications, indiquant une régénération partielle de l’huile usagée. Cependant, la couleur de l’huile traitée est restée inchangée.
Téléchargements
Références
Abir, A. (2016). Clay activation: Modes and structural modifications [Master’s thesis, National Polytechnic School].
Amirouche, L. (2011). Study of the sorption capacity of copper (II), zinc (II), and polyphenols by bentonites under microwave irradiation [Master’s thesis, Mouloud Mammeri University of Tizi-Ouzou].
Amrane, K., & Boubekeur, S. (2017). Chemical regeneration of used dielectric oils using raw bentonite from Maghnia [Master’s thesis, Djilali Bounaama University of Khemis Miliana].
Anisuzzaman, S. M., & Jumadil, N. S. (2024). Used lubricating oil treatment using acid activation clay as adsorbent for oil recovery. Borneo Science Journal, 45(2), 1–12. https://doi.org/10.51200/bsj.v45i2.5880
Armioni, D. M., Rațiu, S. A., Benea, M. L., & Puțan, V. (2024). Overview on the environmental impact of used engine oil. Journal of Physics: Conference Series, 2927(1), Article 012007. https://doi.org/10.1088/1742-6596/2927/1/012007
Ayati, B., Newport, D., Wong, H., & Christophe, C. (2022). Acid activated smectite clay as pozzolanic supplementary cementitious material. Cement and Concrete Research, 162, Article 106969. https://doi.org/10.1016/j.cemconres.2022.106969
Bahranowski, K., Klimek, A., Gaweł, A., Olejniczak, Z., & Serwicka, E. M. (2022). Rehydration driven acid impregnation of thermally pretreated Ca-bentonite—Evolution of the clay structure. Materials, 15(6), Article 2067. https://doi.org/10.3390/ma15062067
Bennoui, S. A., & Haleche, S. (2021). Regeneration of used engine oils by acid treatment and adsorption [Master’s thesis, University of Blida 1].
Berhe, M. T., Gebreyohannes, G., Cheru, M. S., & Weldehans, M. G. (2024). Characterization of acid activation of bentonite clay of Hadar, Afar, Ethiopia. Advances in Materials Science and Engineering, Article 6413786. https://doi.org/10.1155/2024/6413786
Bessaha, F. (2016). Thermal and chemical modification and application of a 1:1 clay for dye co-adsorption [Doctoral thesis, Abdelhamid Ibn Badis University of Mostaganem].
Boudouara, N. (2021). Application of modified clays for pollution control [Doctoral thesis, Mustapha Stambouli University of Mascara].
Cabrera Escobar, M., González Martínez, J., López Ramírez, A., & Fernández Torres, P. (2026). Recycling of used lubricating oils: Environmental and economic perspectives. Recycling, 11(2), 145–160. https://doi.org/10.3390/recycling11020145
Dawood, I., Zyoud, A. H., Zyoud, S., Amireh, A., Zyoud, S. H., & Kim, T. W. (2025). Sustainable water treatment using thermally stable natural clay: Dual adsorption–thermolysis approach for organic pollutants and nitrate removal. Scientific Reports, 15, Article 29888. https://doi.org/10.1038/s41598-025-29888
Derafa, G. (2014). Synthesis and characterization of modified montmorillonite: Application to the adsorption of cationic dyes [Master’s thesis, Ferhat Abbas University Sétif 1].
Dodoo, D., Appiah, G., Acquaah, G., & Dodoo, G., Jr. (2023). Fixed bed column study for the remediation of the bauxite liquid residue using acid activated clays and natural clays. Heliyon, 9(3), Article e14310. https://doi.org/10.1016/j.heliyon.2023.e14310
Fouzia, B. (2015). Zinc adsorption by raw and activated bentonite [Master’s thesis, National Polytechnic School].
Ghafar, A. H., Radwan, E. K., & El-Wakeel, S. T. (2020). Removal of hazardous contaminants from water by natural and zwitterionic surfactant-modified clay. ACS Omega, 5(17), 10042–10052. https://doi.org/10.1021/acsomega.0c00834
Gorączko, A., & Topoliński, T. (2020). Particle size distribution of natural clayey soils: A discussion on the use of laser diffraction analysis (LDA). Geosciences, 10(2), Article 55. https://doi.org/10.3390/geosciences10020055
Grema, A. S., Idriss, I. M., Alkali, A. N., Ahmed, M. M., & Iyodo, H. M. (2021). Production of clay-based ceramic filter for water purification. European Journal of Engineering and Technology Research. https://doi.org/10.24018/ejers.2021.6.7.2623
Hazarika, A., Huang, L., & Babaahmadi, A. (2024). Characterisation, activation, and reactivity of heterogenous natural clays. Materials and Structures, 57, Article 68. https://doi.org/10.1617/s11527-024-02335-9
Heiri, O., Lotter, A. F., & Lemcke, G. (2001). Loss on ignition as a method for estimating organic and carbonate content in sediments: Reproducibility and comparability of results. Journal of Paleolimnology, 25(1), 101–110. https://doi.org/10.1023/A:1008119611481
Al Zubaidi, I., Al Tamimi, A., & Al-Zubaidi, M. (2021). Applications of de-oiling and reactivation of spent clay adsorbents for oil and effluent treatment. Chemical Engineering Journal Advances, 15, Article 100452. https://doi.org/10.1016/j.cengjadv.2023.100452
Islam Sazzad, M. R., Rahman, M., Hassan, T., Al Rifat, A., Al Mamun, A., Adib, A. R., Meraz, R. M., & Ahmed, M. (2024). Advancing sustainable lubricating oil management: Re-refining techniques, market insights, innovative enhancements, and conversion to fuel. Heliyon, 10(20), Article e39248. https://doi.org/10.1016/j.heliyon.2024.e39248
Juraev, T. E., Ismailov, O., Yakubov, Y. Y., & Auesbaev, A. U. (2025). Investigation of the physicochemical properties of recovered oil by determining the optimal amounts of acids and adsorbents in the used oil recycling process. Chemical Problems, (4).
Khan, S., Ajmal, S., Hussain, T., & Rahman, M. U. (2023). Clay based materials for enhanced water treatment: Adsorption mechanisms, challenges, and future directions. Journal of Umm Al-Qura University for Applied Sciences, 11, 219–234. https://doi.org/10.1007/s43941-023-00034-1
Khole, M. S., Tupe, S. K., & Sayyad, S. (2023). Estimating soil moisture content of bare soil using oven drying method. International Journal of Scientific Research in Science and Technology.
Kosmulski, M. (2009). Surface charging and points of zero charge (1st ed.). CRC Press. https://doi.org/10.1201/9781420051896
Kosmulski, M. (2021). The pH of zero point of charge: Review of 50 years of research. Advances in Colloid and Interface Science, 294, Article 102486. https://doi.org/10.1016/j.cis.2021.102486
Liu, T., Li, X., Wang, H., et al. (2024). Reconstructing kaolinite compounds for remarkably enhanced adsorption of Congo red. Molecules, 29(9), Article 2121. https://doi.org/10.3390/molecules29092121
Lo Dico, G., Lisuzzo, L., Carcelén, V., Cavallaro, G., & Haranczyk, M. (2024). Thermogravimetric analysis of moisture in natural and thermally treated clay materials. Materials, 17(10), Article 2231. https://doi.org/10.3390/ma17102231
Ma, J., Ruan, S., Hu, J., Sun, Y., Fei, Y., Jiang, X., Dong, S., Chen, T., & Wu, N. (2020). The intrinsic relationship between color variation and performances of the deteriorated aviation lubrication oil. Journal of Industrial and Engineering Chemistry, 92, 88–95. https://doi.org/10.1016/j.jiec.2020.08.023
Madani, A. (2008). Contribution to the characterization and regeneration of used engine oils by percolation [Master’s thesis, National Polytechnic School].
Madejová, J., & Pálková, H. (2024). Review of the application of infrared spectroscopy in studies of acid-treated clay minerals. Clays and Clay Minerals, 72, Article e30. https://doi.org/10.1017/cmn.2024.24
Madejová, J., Jankovič, L., & Komadel, P. (2006). Identification of phases in thermally treated kaolinite by infrared spectroscopy and thermogravimetry. Clay Minerals, 41(4), 731–741. https://doi.org/10.1180/0009855064140217
Mishra, A., Mishra, S., & Patel, R. (2025). Hydrocarbon pollution and remediation strategies for lubricating oils. Environmental Science and Pollution Research, 32(5), 6789–6802. https://doi.org/10.1007/s11356-025-17890-2
Negasa, B., Alemu, T., Bekele, G., & Tadesse, M. (2025). Characterization of recycled lubricating oils using GC-MS and FTIR. Scientific Reports, 15, Article 11234. https://doi.org/10.1038/s41598-025-11234-7
Osman, A. A., Gad Allah, M. A., & El Sheikh, A. H. (2021). Optimization of acidic activation conditions for natural clay and its application in waste oil bleaching. Egyptian Journal of Chemistry, 64(10), 5167–5179. https://doi.org/10.21608/ejchem.2021.81234
Parekh, K., Gaur, R., & Shahabuddin, S. (2025). Re-refining used oil using rosin: A new approach for recycling waste engine oil. Environmental Progress & Sustainable Energy, 44(6). https://doi.org/10.1002/ep.70072
Ravelomanantsoa, S. (2015). Contribution to the valorization of used motor oils [Master’s thesis, Higher Polytechnic School].
Rezaiguia, W. (2017). Removal of methylene blue by adsorption on natural and treated kaolin [Master’s thesis, Larbi Ben M’hidi University, Oum El Bouaghi].
Sabadash, V., Ivanova, N., & Petrenko, O. (2024). Adsorption of oil products by natural and modified sorbents. Clean Technologies and Environmental Policy, 26(3), 455–468. https://doi.org/10.1007/s10098-024-02345-1
Saed, S. A., & Al-Mammar, D. E. (2021). Influence of acid activation of a mixture of illite, kaolinite, and chlorite clays on the adsorption of methyl violet 6B dye. Iraqi Journal of Science, 62(6), 1761–1778. https://doi.org/10.24996/ijs.2021.62.6.2
Sarkar, B., Rusmin, R., Ugochukwu, U. C., Mukhopadhyay, R., & Manjaiah, K. M. (2019). Modified clay minerals for environmental applications. In B. Sarkar, R. Rusmin, U. C. Ugochukwu, R. Mukhopadhyay, & K. M. Manjaiah (Eds.), Modified clay and zeolite nanocomposite materials (pp. 1–25). Elsevier.
Sarkar, S., Banerjee, R., Chatterjee, P., & Das, K. (2023). Low cost adsorbents for regeneration of used lubricating oils. Journal of Material Cycles and Waste Management, 25(4), 1890–1902. https://doi.org/10.1007/s10163-023-01567-9
Sarkar, S., Datta, D., Deepak, K. S., Mondal, B. K., & Das, B. (2023). Comprehensive investigation of various re-refining technologies of used lubricating oil: A review. Journal of Material Cycles and Waste Management, 25, 1935–1965. https://doi.org/10.1007/s10163-023-01562-7
Sorrentino, G., Chellappah, K., & Biscontin, G. (2025). Understanding clogging mechanisms in filter media: An integration of laboratory findings and theoretical perspectives. Separation and Purification Technology, 330, Article 130602. https://doi.org/10.1016/j.seppur.2024.130602
Stan, C., Andreescu, C., & Toma, M. (2018). Some aspects of the regeneration of used motor oil. Procedia Manufacturing, 22, 709–713. https://doi.org/10.1016/j.promfg.2018.03.102
Taxiarchou, M., Tsakiri, D., & Douni, I. (2025). The impact of pH on the pore and structural characteristics of acid-modified bentonites in oxalate solutions. Minerals, 15(3), Article 257. https://doi.org/10.3390/min15030257
Touir, I. F. Z., & Taleb, S. (2019). Regeneration of Askarel oil [Master’s thesis, Mohamed Boudiaf University of M’sila].
Ugwele, F. O., Aninwede, C. S., Chime, T. O., Asadu, O. C., & Innocent, S. (2020). Application of response surface methodology in optimizing the process conditions for the regeneration of used mobil oil using different kinds of acids. Heliyon. https://doi.org/10.1016/j.heliyon.2020.e05062
Wang, Y., Xu, H., Gao, L., Yan, M., Duan, H., & Song, C. (2019). Regeneration of spent lubricant refining clays by solvent extraction. Journal of Chemistry. https://doi.org/10.1155/2019/1234567
Zahaf, F. (2017). Structural study of modified clays applied to pollutant adsorption [Doctoral thesis, Mustapha Stambouli University of Mascara].
Zhang, J., Li, Y. H., & Chen, X. (2022). Evaluation of loss on ignition method for organic matter determination in agricultural soils. Soil Science Society of America Journal, 86(3), 456–468. https://doi.org/10.1002/saj2.20234
Téléchargements
Publiée
Numéro
Rubrique
Licence
(c) Copyright Mulumba et al. 2026
Ce travail est disponible sous licence Creative Commons Attribution - Pas d’Utilisation Commerciale - Partage dans les Mêmes Conditions 4.0 International.
